|
None |
Program
already exists |
|
|
100 |
Program
does not exist |
3/13/01 |
|
101 |
Error
reading program |
3/13/01 |
|
102 |
Format
error |
3/13/01 |
|
103 |
Internal
structure error |
|
|
104 |
Error
during KERF calculation |
|
|
105 |
Station
reports |
|
|
108 |
Frequency
error in <n> axis |
1/16/01 |
|
109 |
Deviation
error in <n> axis at speed <m> |
1/16/01 |
|
110 |
Cable
fault <n> axis |
1/23/01 |
|
111 |
Constants
not found |
|
|
112 |
Error
writing <n> |
|
|
113 |
Error
loading machine interface program |
|
|
115 |
Memory
overflow |
|
|
116 |
Drive
not ready |
|
|
119 |
Machine
still moving |
12/11/00 |
|
121 |
System
error in standard shapes |
|
|
122 |
Constant
too long |
|
|
123 |
Invalid
symbol @ |
|
|
124 |
Invalid
parameter |
|
|
125 |
Error
in offset |
|
|
126 |
Error
using #F+ |
|
|
127 |
Invalid
number of signs |
|
|
128 |
Smoothing
error |
|
|
129 |
Axes
too short (with #K or #R) |
|
|
130 |
Found
blank line |
|
|
131 |
Error
in SKIP function |
|
|
132 |
Calculation
error |
|
|
133 |
Process
still running |
|
|
134 |
Select
process first |
|
|
135 |
ALFE
reports error <n> |
|
|
136 |
Auxiliary
function <n> replaced <m> times by
<o> |
|
|
137 |
<n>
key pressed |
|
|
138 |
Servicing
mode activated |
|
|
143 |
Function
not admissible during program run. Set initial
screen in movement window. |
|
|
144 |
End
function! |
|
|
145 |
Complete
program execution |
|
|
147 148 149 150 |
Wrong
parameter interface <n> |
|
|
151 |
Marked
section too large |
|
|
152 |
Program
extent too large |
4/3/01 |
|
153 |
Floppy
disk <0 | 1> is write protected |
|
|
154 |
Floppy
disk is full |
|
|
155 |
Floppy
disk: general error <m> |
2/20/01 |
|
156 |
Error
reading from <n> |
|
|
158 |
Macro
definition file not found |
|
|
159 |
Syntax
error in MACRO definition file |
|
|
160 |
Watchdog |
1/30/01
|
|
161 |
ASIOB/ATHC-2
error |
1/30/01
|
|
162 |
Error
control panel |
1/16/01 |
|
163 |
Emergency
stop chain interrupted |
1/16/01 |
|
164 |
#
<n> format error |
|
|
165 |
#
<n> circle error |
|
| 166 |
# <n> loss
auxiliary function |
|
| 167 |
# <n> loss
comment |
|
| 168 |
# <n> loss
geometry |
|
| 169 |
# <n> Center or
end point greater than 1.3 miles |
|
| 170 |
Free <n> axis
from reference cam |
|
| 171 |
Definition for station
<n> not found |
|
| 172 |
Error writing
<n> |
|
| 174 |
Force list is
full |
|
| 175 |
Timeout |
|
| 177 |
Transfer
aborted |
|
| 180 |
Invalid constants at
station <n>. Execute download! |
|
| 181 |
Download error at
station <n> |
|
| 182 |
Power supply
interrupted at station <n> |
1/16/01 |
| 183 |
Turn on 24 Volt
Power |
1/30/00 |
| 184 |
No response from
station <n> |
1/23/01 |
| 185 |
Automatic reference
movement not possible, check machine
constants |
|
| 186 |
Battery RAM checksum
error <n> |
1/16/01 |
| 187 |
Incompatible floppy
disk format |
|
| 195 |
No potentiometer
data |
|
| 200 |
Too many input
variables |
|
| 201 |
For renewed processing
- select program again |
|
| 202 |
<X Y Y2 P> axis
reached software limit switch |
1/16/01 |
| 203 |
Too many data blocks
for program preparation |
|
| 204 |
Reference necessary for
this function |
4/3/01 |
| 205 |
Set reference position
of main tool first |
|
| 206 |
Reference position of
main tool already set |
|
| 207 |
PPT active |
|
| 208 |
<Type of error>
in function <Mathematical function>. System
is unstable!! |
|
| 209 |
Division by zero at
<n>: <m> |
|
| 210 |
Caution, invalid system
configuration! |
4/3/01 |
| 212 |
Closed
contour |
|
| 213 |
# <n> too
long |
|
| 214 |
Function
aborted |
|
| 215 |
Error reading cutting
data files |
|
| 216 |
No cutting data
available |
|
| 217 |
No valid cutting data
stored |
|
| 218 |
Excessive nesting of
subroutines |
|
| 220 |
ALFE - 24-volt supply
missing |
|
| 221 |
ALFE - 15-volt supply
missing |
|
| 222 |
ALFE - DMA
error |
|
| 223 |
Internal logging error
A:<n> D:<m> B:<o> |
4/3/01 |
| 224 |
IMAJE timing error,
status <n> |
|
| 225 |
IMAJE does not
understand, status <n> |
|
| 226 |
Distance between
carriages Y<n> and Y<m> too small.
Tangential follower not in basic
position. |
|
| 227 |
Plate thickness
<n> not available in the organizational
program <m>. |
|
| 228 |
Next smaller plate
thickness <n> will be used |
|
| 230 |
# <n> angle
larger than tangential range of unit |
|
| 231 |
Directory transfer
active |
|
| 232 |
Measuring point cannot
be reached |
|
| 233 |
This function is, at
the moment, blocked by another function. |
|
| 234 |
Block <n> /
offset <m> not found in file
<o> |
|
| 235 |
Label <n> not
found in file <m> |
|
| 236 |
Sensor
triggered |
|
| 237 |
Please wait, MIP being
initialized. |
|
| 238 |
Memory management error
in module <n> |
|
| 239 |
Chamfering with
variable angles in circular arcs not possible in
line <n>, because the arc is larger than a
quadrant |
|
| 241 |
Please restart control
system now! |
|
| 242 |
Servicing mode
deactivated |
|
| 243 |
Y1 carriage must be
travelling during plate alignment |
|
| 246 |
Syntax error in file
%s |
|
| 250 |
Error <n> while
calibration of sensor |
|
| 251 |
Error <n> while
calibration of angle |
|
| 252 |
Height sensor reports
error <n> |
|
| 253 |
Order of unknown
variable <n> |
|
| 254 |
Unknown telegram
<n> : <m> |
|
| 255 |
Please power on
MC |
|
| 257 |
Connection-error to
MC |
|
| 258 |
OC reports
synchronization failure with MC |
|
| 259 |
MC reports
synchronization failure with OC |
|
| 260 |
Checksum-error while
transmitting constant group <n> |
|
